Mustang Parts › Mustang Short Throw Sport Shifter (All 83 - Early 01 & 01-04 V6 T-5/T-45 Transmission) - Installation Instructions
Share

Mustang Short Throw Sport Shifter (All 83 - Early 01 & 01-04 V6 T-5/T-45 Transmission) - Installation Instructions

This Mustang Parts Installation Guide Works For

Short Throw Sport Shifter for T-5/T-45 (82-Early 01 V8; 93-99 Cobra; 94-04 V6)Short Throw Sport Shifter for T-5/T-45 (82-Early 01 V8; 93-99 Cobra; 94-04 V6)
Fitment Includes:
  • - V6 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004
  • - GT 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001
  • - Cobra 1994, 1995, 1996, 1997, 1998, 1999
  • - Bullitt 2001
  • - Foxbody 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993
DOWNLOAD PDF

Tools Required

  • Socket Wrench
  • 8 mm Socket
  • 10 mm Socket
  • 13 mm Socket
  • 14 mm Socket
  • 4 mm Allen Wrench
  • 5 mm Allen Wrench
  • 6 mm Allen Wrench
  • 8 mm Allen Wrench
  • Silicone Gasket Maker
  • Needle-Nose Pliers
  • Razor Blade
  • 8, 10, 13 and 14mm Wrenches (Used where sockets don't fit)
Installation Time: 60 Mins

Installation

  1. image2

  2. Remove shifter knob by twisting it off.

    image3

  3. Remove shifter console trim, which should pop off with a bit of force. Make sure the metal clips are attached to the 4 tabs for reinstallation.

    image4

  4. Remove leather shifter boot by pulling it up.

    image5

  5. Using the 10mm socket, remove the two screws attaching the shifter handle to the shifter and remove the old shifter handle.

    image6

  6. Use the 8 mm socket wrench to remove the two visible bolts retaining the metal ring around the second shifter boot. Then use an 8 mm wrench to remove the two bolts securing the front of the metal ring. This may take a while, unless you want to remove the whole console. If you don’t remove the console, you will need to use the needle nose pliers to remove the staple holding the rubber boot to the metal retaining ring. You will then be able to move the rubber boot out of the way when necessary.

    image7

  7. Now you have access to the shifter. Use a 13 mm wrench and/or socket wrench to remove the 4 bolts securing the shifter to the transmission.

    image8

  8. Lift the old shifter out of the way. This may require some force as the old silicone is still holding it to the transmission. Be careful trying not to let dirt or dust fall into the transmission.

    image9

  9. Use the razor blade to fully remove the old silicone to prepare the surface for the new shifter.

    image10

  10. With the 4 mm Allen wrench, attach the four screws to the transmission in preparation for the new shifter. Make sure they are tight.

    image11

  11. Set the new shifter in to check fitment, be sure to remove the shifter bushing from the bottom of old shifter and transfer it over to the new shifter. Using the 6 mm Allen wrench, adjust the screws included with the kit so that when the transmission is in gear, there is only a small gap between the shifter and the end of the screw (~1/16”). Then fasten the nut to hold the screws tight. Also make sure the transmission shifts through all the gears as it should.

    image12

  12. Remove the shifter and apply a bead of silicone all the way around the surface, to be bonded to the transmission as shown Be sure to follow instructions on silicone package for proper use.

    image13

  13. Position the new shifter on the screws already installed, which will make attachment simple. Push the new shifter all the way down and attach the four, 14 mm nuts until tight.

    image14

  14. Again, verify that the shifter shifts it through all the gears properly. Reinstall the rubber boot over the new shifter and fasten the ring using the four, 8 mm bolts removed earlier, making sure the rubber boot is secured properly.

    image15

  15. Using the 5 mm Allen wrench and the screws provided in the kit, attach the new shifter handle to the new shifter as shown. When attaching the new handle, select the height you want, as the new kit has two height settings, as shown in the height comparison photo earlier. Use the top two holes for the medium height or the bottom two holes for the low height setting.

    image16

  16. Replace leather shifter boot over new shifter and reinstall the shift knob.

    image17

  17. Snap the shifter console trim back on and you’re done. If you have time, however, you may want to wait to give the silicone proper drying time, as instructed by silicone package (usually about 24 Hrs if possible).

    image18

  18. Enjoy your new shifter!


Installation instructions provided by AmericanMuscle customer Callaway Turner 12.23.08

Continue Shopping